>

NOISEBLOCK Modular Panel Enclosure Systems

in standard galvanized steel, Type G90, mill phosphatized (satin) finish galvanized steel (readily paintable), stainless steel, Types 304 and 316, aluminum and aluminized steel. Standard material gages for solid outer shell are 18 ga. and 16 ga., perforated (23% open area) inner shell is 22 gage. Septum panels and

>

NOISEBLOCK™ Acoustic Enclosures - Kinetics Noise

Outer and inner shell materials are available in standard galvanized steel, Type G90, mill phosphatized (satin) finish galvanized steel (readily paintable), stainless steel, Types 304 and 316, aluminum and aluminized steel. Standard material gages for solid outer shell are 18 ga. and 16 ga., perforated (23% open area) inner shell is 22 gage. ...

>

SECTION 221423 – STORM DRAINAGE PIPING SPECIALTIES

galvanized, mill-phosphatized finish for painting if indicated. C. Elastic Membrane Sheet: ASTM D 4068, flexible, chlorinated polyethylene, 40-mil (1.01-mm) minimum thickness. D. Fasteners: Metal compatible with material and substrate being fastened. E. Metal Accessories: Sheet metal strips, clamps, anchoring devices, and similar accessory units

>

Murray 135 Amp Overhead/Underground Meter Socket …

Zinc-coated G-90 steel body construction with a mill-phosphatized finish and a polyester-resin finished base Duplex neutral/neutral design Single-phase, 3-wire, 135 Amp, …

>

Buildings | Steel & Aluminum | Easy to Install ...

Zinc-Coated (Galvanized) Steel Sheet: ASTM A 653/A, commercial quality, G90 (Z275) coating designation; mill phosphatized. Aluminum Treadplate: 1/8-inch aluminum plate conforming to ASTM B 209. Steel Mechanical Tubing: ASTM A 513, welded steel mechanical tubing. Expanded Polystyrene (EPS) Core: Minimum of .95 pcf complying with ASTM C-578 Type 1.

>

Project to Re-Roof Fire Station 12 March 30, 2017 City of ...

1. Finish: Mill phosphatized. 2. Color: Manufacturer's standard. E. Construction: 1. Curb Profile: Manufacturer's standard. compatible with roofing system. 2. Nailer: Factory-installed continuous wood nailers . 5-1/2 inches continuous around support perimeter. 3. Platform Cap: Where portion of equipment support is not covered by equipment, provide

>

SECTION 23 3300

Exposed-Surface Finish: Mill phosphatized. Aluminum Sheets: Comply with ASTM B209, Alloy 3003, Temper H14; with mill finish for concealed ducts and standard 1-side bright finish for exposed ducts. Extruded Aluminum: Comply with ASTM B221, Alloy 6063, Temper T5 [T6].

>

Increasing topcoat adhesion for solvent phosphatized ...

The phosphatized surface is obtained from a composition that can contain methylene chloride, as well as water in minor amount, and yet maintain a continuous and homogeneous liquid phase. ... Additional suitable paints can include the oil paints and the paint system may be applied as a mill finish. Before applying the phosphate coating, it is ...

>

Mill Finish Aluminum Foil

Mill Phosphatized Finish- Aluminum/Al Foil,plate/sheet. mill phosphatized finish . If you have any questions or good suggestions on our products and site, or if you want to know more information about our products, please write them and send to …

>

TOILET COMPARTMENTS ACCEPTABLE MANUFACTURERS

a. Steel Sheets for Color-Coated Finish: Provide mill-phosphatized steel sheet that is leveled to stretcher-leveled flatness complying with the requirements of standards indicated below: 1) Hot-Dip Galvanized Steel Sheet: ASTM A 653, Class C, of the following minimum thicknesses: a) Pilasters (Overhead Braced): 0.0359 inch.

>

Different Types of Metal Decking Finishes (+ Lead Times)

Phosphatized and painted metal decking. This is metal decking in which the top of the deck is not galvanized or painted. The bottom of the material will have a prime painted finish. Metal deck with this specification will be used as a 1.5", 2", or 3" deep floor deck. However, you cannot paint the top of the metal decking because the paint ...

>

SECTION 077200 - ROOF ACCESSORIES

Mill-Phosphatized Finish: Manufacturer's standard for field painting. Factory Prime Coating: Where field painting is indicated, apply pretreatment and white or light-colored, factory-applied, baked-on epoxy primer coat, with a minimum dry film thickness of 0.2 mil (0.005 mm).

>

Section 15815 - Metal Ducts Rev1

designation; mill-phosphatized finish for surfaces of ducts exposed to view. B. PVC-Coated Galvanized Steel: UL 181, Class 1 listing. Lock-forming-quality, galvanized, sheet steel with ASTM A 653/A 653M, G90 coating designation; factory-applied, 4-mil PVC coating on exposed surfaces of ducts and fittings (exterior of ducts

>

San Jose City College PE Building &Wellness Center ...

1-1/4 ounces per square foot total both sides; ducts to have mill-phosphatized finish for surfaces exposed to view. C. Stainless Steel: ASTM A 480/A 480M. D. Aluminum Sheets: ASTM B 209 (ASTM B 209M), alloy 3003, temper H14; with mill finish for concealed ducts and standard, 1-side bright finish for exposed ducts.

>

Material Specification Sheet Phosphatized Bonderized

Paintgrip material is phosphatized – sometimes referred to as "bonderized" ‐ at the mill which allows the user to paint in the as‐received condition. This phosphate coating provides enhanced paint adhesion and improved corrosion resistance

>

Austin Mohawk and Company, Inc. Prefabricated Metal ...

Zinc-Coated (Galvanized) Steel Sheet: ASTM A 653/A, commercial quality, G60 (Z180) coating designation; mill phosphatized. D. Aluminum Treadplates: 1/8-inch aluminum plate conforming to ASTM B 209. E. Steel Mechanical Tubing: ASTM A 513, welded steel mechanical tubing. F.

>

23 31 13 Metal Ducts

have mill-phosphatized finish for surfaces exposed to view. C. Reinforcement Shapes and Plates: Galvanized-steel reinforcement where installed on galvanized sheet metal ducts. D. Tie Rods: Galvanized steel, 1/4-inch minimum diameter for lengths 36 inches or less; 3/8-inch minimum diameter for lengths longer than 36 inches.

>

Specifying Paintgrip - Linx Industries, Inc.

Project specification requirements for paintgrip or mill-phosphatized finishes added to the galvanized coating for exposed ductwork have the ultimate intentions of providing a paintable surface. In theory the "acid" etching of the surface is to provide additional "bite" to the paint and enhances the adhesion of the paint to the underlying surface.

>

CHABOT - LAS POSITAS COMMUNITY COLLEGE DISTRICT …

Galvanizing: 1-1/4 ounces per square foot total both sides; ducts to have mill-phosphatized finish for surfaces exposed to view. C. Stainless Steel: ASTM A 480/A 480M. D. Aluminum Sheets: ASTM B 209 (ASTM B 209M), alloy 3003, temper H14; with mill finish for concealed ducts and standard, 1-side bright finish for exposed ducts.

>

CHABOT - LAS POSITAS COMMUNITY COLLEGE DISTRICT …

Ducts to have mill phosphatized finish for surfaces exposed to view. 2. Aluminum Ducts: ASTM B 209 (ASTM B 209M); aluminum sheet, alloy 3003-H14. Aluminum Connectors and Bar Stock: Alloy 6061-T651 or of equivalent strength with mill finish for concealed ducts and standard, 1-side bright finish for exposed ducts.

>

mill phosphatized finish- Aluminum/Al foil,plate/sheet ...

mill phosphatized finish . If you have any questions or good suggestions on our products and site, or if you want to know more information about our products, please write them and send to us, we will contact you within one business day.

>

Michigan State University AIR DUCT ACCESSORIES ...

2. Exposed-Surface Finish: Mill phosphatized C. Stainless-Steel Sheets: Comply with ASTM A 480/A 480M, Type 304. D. Aluminum Sheets: Comply with B 209 (ASTMASTM B 209M), Alloy 3003, Temper H14; with mill finish for concealed ducts …

>

SECTION 233113 - METAL DUCTS PART 1 - GENERAL

Finishes for Surfaces Exposed to View: Mill phosphatized. C. Aluminum Sheets: Comply with ASTM B 209 (ASTM B 209M) Alloy 3003, H14 temper; with mill finish for concealed ducts, and standard, one-side bright finish for duct surfaces exposed to view.

>

Round Spiral Duct for HVAC Duct Systems | Fabricator ...

Materials – G90 and G60 galvanized steels, "paint-grip" mill phosphatized steel, A-60 galvanealed steel, black iron, aluminized steel, 3003 aluminum, 304-L and 316-L stainless steels, PCD Polyvinyl Coated Duct, Agion anti-microbial steel.

>

SECTION 23 31 13

Provide mill-phosphatized finish for surfaces of ducts exposed to view. Stainless Steel Ducts: ASTM A 480/A 480M, Type 316 sheet form with No. 4 finish for surfaces of ducts exposed to view, and Type 304 sheet form with No. 1 finish for concealed ducts.

>

Product Catalog and Specifi cations

quality, hot-dip galvanized steel sheet with 0.20 percent copper, mill phosphatized where indicated for painting; not less than 0.0.0635 inch thick, unless otherwise indicated. [NOTE TO SPECIFIER: Delete if aluminum materials are not specified.] 2.03 ALUMINUM FINISHES A. Spray Finish 1.

>

Sorry, we have detected unusual traffic from your network.

Sorry, we have detected unusual traffic from your network. Please slide to verify help help

>

DESIGN STANDARDS YSM APPENDIX Section II. Divisions 1 - …

hot-dip galvanized, mill phosphatized. B. Stainless Steel: AISI Type 302/304, ASTM A167, 2D annealed finish except as otherwise indicated, temper as required for forming and performance. C. Aluminum Sheet: ASTM B209, alloy 3003, temper as required for forming and performance; A-C22A41 clear anodized finish, except mill finish